Home > FITTINGS & VALVES > Watts & Sea Tech Fittings LF47 & 35 Series Quick Connect > Tees Watts LF47 & 35 Series

Tees Watts LF47 & 35 Series

Push Fittings Hold Up To 250 PSI, 1 Piece, No Parts To Assemble Or Lose, Code Approved For Behind Wall Without Access & Direct In Ground Burial Installations, NSF-14, NSF-61, CSA/ASTM & UPC Code Listed & Approved, Replacement For Qest & Flare It Type Fittings. Material Specifications Series 35 All Series 35 products are approved and certified to NSF-61-G, NSF 14, CSA B137.5, ASTM F877, and to the Uniform Plumbing Code (U.P. Code) and ASSE 1061. Series 35 products are available in standard imperial inch sizes. Squarely cut the plastic,copper or CPVC tubing and snap a Watts Quick-Connect fitting in place for a zero leak connection. Watts strongly recommends that new installations be thoroughly tested prior to use.

Body: Polysulfone
Collet: Nylon
O-Ring: EPDM
Spacer: Acetal
Tube Liner: Polysulfone
Collet Clip: Delrin
Click the part # in the list below for image, info and a closer look
Scroll for more Info, Specs & Related Items.
14-21 Day ETA for Out of Stock/Non-Stock Items in this Category

Products (Total Items: 1)

Part #

Image

Description

Stock

Price

Quantity

3524RB-101004

1/2"x1/2"CTS x 1/4"od Tube Tee Reducer SeaTech Watts 0650033

Non-Stock Pre-Order

$10.84

Material Specifications Series 35

Body: Polysulfone
Collet: Nylon
O-Ring: EPDM
Spacer: Acetal
Tube Liner: Polysulfone
Collet Clip: Delrin

Watts Quick-Connect Series 35 products are designed and manufactured to be trouble free for many years of service life. Series 35 products are designed and manufactured in polysulfone, a high performance thermal plastic material. All Series 35 products are approved and certified to NSF-61-G, NSF 14, CSA B137.5, ASTM F877, and to the Uniform Plumbing Code (U.P. Code) and ASSE 1061. Series 35 products are available in standard imperial inch sizes. The Watts Quick-Connect design allows for quick and easy connections without installation tools. Simply cut the plastic,copper or CPVC tubing and snap a Watts Quick-Connect fitting in place for a zero leak connection. Watts Quick-Connect Series 35 fittings are designed for potable water systems. For other applications please refer to WATTS Technical Service Department. Tubing should be supported at minimum of 36" to prevent excessive load to the connectors. Do not install tubing supports closer than 3 inches from the connector ends. We strongly recommend that new installations be thoroughly tested prior to use. Do not use with explosive gases, petroleum products, or other fuels.

CAUTION!!

The polysulfone material used in the Quick-Connect fittings can be compromised by exposure to volatile organic compounds (VOC’s) and caustic chemicals. Therefore, DO NOT expose this product to any such chemical or foreign substance, which would include exposure to the following products: Pipe Dopes (thread sealants), bug sprays, lubricants, cleaners, paints, bleaches, acids, solder fluxes, plastic piping primers and cements, oxidizing agents, alkaline solutions, thinners, fuels, oil based caulks, hydrocarbons, spray foam of foaming agents (insulation). Watts recommends that all fittings and parts be stored in their original packaging until installation to protect the fitting internals from dirt and debris that may cause damage to the o-ring and the o-ring guide. It is also recommended that all threaded connections be made with Teflon tape only. Failure to follow these instructions will void the warranty and possibly result in leaks and water damage.